language
中国
韩国
韩国
韩国
韩国
韩国
banner

Diamond segment for sandstone cutting should pay attention to what issues

  • Categories:Industry news
  • Author:
  • Origin:
  • Time of issue:2021-07-16 10:51
  • Views:

(Summary description)Diamond segment for sandstone cutting should pay attention to what are the problems, the following Diamond segment for sandstone cutting manufacturers will take you to find out.

Diamond segment for sandstone cutting should pay attention to what issues

(Summary description)Diamond segment for sandstone cutting should pay attention to what are the problems, the following Diamond segment for sandstone cutting manufacturers will take you to find out.

  • Categories:Industry news
  • Author:
  • Origin:
  • Time of issue:2021-07-16 10:51
  • Views:
Information

Diamond segment for sandstone cutting should pay attention to what are the problems, the following Diamond segment for sandstone cutting manufacturers will take you to find out:

customized Diamond segment for sandstone cutting on sales
1. Idling: Especially when the new base is used for the first time, it needs to be idling for about 30 minutes. In the summer high temperature season, it needs to be idling with water. The purpose is to further eliminate the influence of the welding head on the base and enhance the high-speed rotation of the saw blade.
Keep the internal quality of memory in the state.
2. The blocks should not be less than 0.5m3, and they should be placed securely. The bottom surface should be padded with square wood, the plugs should be solid, and the blocks should be located in the working area.
The symmetrical position of the platform is to ensure the stability of the work trolley and the blocks, and there should be no shaking or shaking.
3. Adjust the travel switch according to the length, width and height of the block, so that the lifting of the saw blade and the travel of the feed cart are within a reliable and effective range. The manufacturer of Diamond segment for sandstone cutting tells you that the edge of the saw blade should be up to 10-20mm away from the block before sawing. After sawing, there should be a distance of 20-40mm between the saw blade and the bottom of the block. Before the saw blade moves around, the saw blade should be removed from the block saw. The distance should not be less than 150-200mm to prevent the saw blade from hitting the waste. material.
4. Trial cutting can be performed after the saw blade is idling and stable. The manufacturer of Diamond segment for sandstone cutting tells you not to start the saw blade when the saw blade is in contact with the block, and it is not allowed to stop the rotation of the saw blade during cutting. You must exit the saw blade. Stalled.
5. If you find that the blocks are shaking during cutting, you should stop cutting immediately. After the blocks are firmly fixed, you can continue working. During cutting, you are not allowed to move the blocks arbitrarily.
6. It is found that the saw blade slows down significantly or even clamps the knife during cutting. It may be due to belt slippage, loosening of the compression nut or too deep knife depth, too fast cutting speed, etc., which should be adjusted in time.
7. The linear speed should be compatible with the hardness and wear resistance of the processed stone. Diamond segment for sandstone cutting manufacturers recommend choosing the following linear speed to cut different types of stone.
Tip: When the online speed is not high, increasing the cutting efficiency will reduce the life of the saw blade.
8. The feed speed mainly depends on the performance of the material to be processed. For each material, there is a certain range of feed speeds when the cutting depth is constant. The manufacturer of Diamond segment for sandstone cutting tells you that if the speed is too high, the diamond will speed up. Wear and even fall off, causing the saw blade to consume too fast. If the speed is too low, the self-sharpening process of the saw blade will not be carried out normally, and the cutting ability will be lost due to "blunting and slipping". Diamond segment for sandstone cutting manufacturers tell you that under normal circumstances, the feed speed should be slow during cutting, and should be even during sawing. For common typical materials, when the cutting depth is 20mm, the following feed speed table is recommended for your reference. When the thickness changes, the cutting speed can be converted according to the cutting area (cm2/min).
Tip: The first entry or the first three walks of each board should be halved.

Keyword:

Scan the QR code to read on your phone

Xinguang Diamond

WeChat official account

Xinguang Diamond

Mobile phone QR code

Tel: 86 15179308190
Fax: 86 0793-5226507
Email: andy@chinaxinguang.com
Address: Industrial Park, tianfanjie Town, Poyang County, Jiangxi Province

Copyright: Jiangxi Xinguang Diamond Tools Co., Ltd
Gan ICP Bei no.12002000

This website supports IPv4 / IPv6 accessebsite construction: 300.cn-Nanchang