Customized diamond tools for concrete products are cutting and demolition tools for mines, waste materials, arc slabs, large slab stones, thick concrete, irregular concrete reinforcement, bridges and roads. The customized diamond tools for concrete is convenient and flexible. It can be cut horizontally and vertically. In order to better improve the working efficiency and service life of customized diamond tools in china. It is important to use customized diamond tools for concrete correctly. Next, the manufacturer of concrete diamond tools will take you to know the precautions for the use of customized diamond tools for concrete in china.

All kinds of materials disassembled after cutting customized diamond tools for concrete shall be cleaned up in time and stacked in designated places by classification. Superstructure waste shall be dumped in a tumbling barrel, which shall not be thrown down from high places at will, and shall be cleared and transported in time. The materials and construction waste removed by concrete cutting shall be cleaned up in time, and it is strictly prohibited to throw them down from high altitude. The materials disassembled by concrete diamond tools shall be unloaded by vertical lifting equipment or chute, and the construction waste shall be unloaded by garbage shaft. The demolition of concrete beam and support beam shall be carried out in sections, and vertical cross operation is not allowed.

In addition, the holes cut by diamond wire saw shall be closed, and multiple people are strictly prohibited from gathering or stacking materials on the floor. When the customized diamond tools for concrete in china is used to remove the concrete beam, ensure that its falling is effectively controlled, then cut off the reinforcement at both ends and put it down slowly end by end. When cutting and removing the concrete support beam column with a rope saw, the reinforcement shall be chiseled along the bottom of the column, and the manual chain fall shall be used for directional traction. The reinforcement on three sides of the column shall be cut by gas welding, and the reinforcement on the front of the traction direction shall be retained. When cutting and removing pipes and containers with a rope saw, the types and chemical properties of the residues must be found out, and the removal construction can be carried out only after corresponding measures are taken.

Precautions for use of customized diamond tools for concrete in china:

1. Be sure to turn off the power supply before turning on the power supply of customized diamond tools for concrete. The operation box or switch must be intact and equipped with grounding protection.

2. When adjusting the left and right position and direction of the driving flywheel of customized diamond tools for concrete, it is necessary to see whether there are obstacles around and whether they will touch other parts of the equipment. When the flywheel driven by concrete diamond tool is adjusted to the end point of the left and right position, the adjustment shall be stopped immediately to avoid damaging the screw nut or burning the motor winding. The customized diamond tools for concrete manufacturer strongly recommends not to adjust the customized diamond tools for concrete to the left and right end positions. The driving flywheel of the customized diamond tools for concrete shall not turn to the vertical upward position, otherwise it may damage the cable of the main motor.

3. When cutting customized diamond tools for concrete in china, always check the supply of cooling water. Once the cooling water supply is not in place, stop cutting immediately to avoid damaging the diamond bead rope.

4. It is forbidden to cut and dismantle customized diamond tools for concrete with wire saw when the power supply is out of phase.

5. When cutting the separated body with customized diamond tools for concrete in china, the principle of cutting the horizontal plane first and then the vertical plane should be followed. In the process of horizontal cutting, support wedges shall be added to the finished cutting saw slot in time to prevent local rock falling and pressing the diamond string rope, resulting in scrapping and accidents of diamond string rope. If necessary, wedge support separators can also be inserted into the vertical saw slot.

6. If the customized diamond tools for concrete equipment shell is found to be charged during operation, it shall be shut down immediately for inspection, and the machine can be started up for concrete cutting and removal after troubleshooting.

7. Regularly check the connection of lines, terminals and connectors of customized diamond tools for concrete cutting machine. In case of problems, take immediate measures to ensure the normal operation of concrete diamond tool cutting equipment.

8. The lever shaft shall be intact and rotate flexibly and reliably, and shall be locked with nuts after assembly with the lever.

9. In case of emergency during the operation of customized diamond tools for concrete equipment, the "emergency stop button" on the console shall be pressed immediately, and the "emergency stop button" can be reset only when safety is ensured.

10. It is forbidden for non professionals to modify the parameters set in the frequency converter of customized diamond tools for concrete.

11. When using customized diamond tools for concrete, the rotation direction shall be kept away from nearby workers as far as possible, and the cut materials shall not extend into the sidewalk.

12. The position of the driving flywheel cannot be adjusted when the customized diamond tools for concrete is in normal cutting operation, and the sawing operation cannot be carried out when the position of the driving flywheel is adjusted.

13. After replacing the diamond saw blade, the customized diamond tools for concrete in china shall be tested for obvious vibration. It can only be used after confirming that it operates normally.

14. In case of severe weather such as thunderstorm or rainstorm, stop the operation of customized diamond tools for concrete as soon as possible and turn off all switches in time. If necessary, transfer the concrete cutting equipment to a safe position to avoid danger.

15. The power supply and all switches must be turned off after the customized diamond tools for concrete cutting operation or before leaving work. After cleaning, place the diamond rope saw.