language
中国
韩国
韩国
韩国
韩国
韩国
banner

Precautions for the use and maintenance of 350mm diamond saw blade products

  • Categories:Industry news
  • Author:
  • Origin:
  • Time of issue:2021-08-11 10:57
  • Views:

(Summary description)350mm diamond saw blade products play a very important role in life. Woodworking cannot start well without 350mm diamond saw blade. The importance of 350mm diamond saw blade is self-evident.

Precautions for the use and maintenance of 350mm diamond saw blade products

(Summary description)350mm diamond saw blade products play a very important role in life. Woodworking cannot start well without 350mm diamond saw blade. The importance of 350mm diamond saw blade is self-evident.

  • Categories:Industry news
  • Author:
  • Origin:
  • Time of issue:2021-08-11 10:57
  • Views:
Information

350mm diamond saw blade products play a very important role in life. Woodworking cannot start well without 350mm diamond saw blade. The importance of 350mm diamond saw blade is self-evident. So do you know what precautions should be taken in the use and maintenance of 350mm diamond saw blade?

Wholesale 350mm diamond saw blade factory1. Please hang the alloy 350mm diamond saw blade vertically on a dry shelf. Be sure to avoid wet places. Never place the alloy 350mm diamond saw blade flat on the ground or on a shelf. Placing it flat will result in the alloy 350mm diamond saw blade. Deformed.
2. To store 350mm diamond saw blade, the 350mm diamond saw blade should not be stacked together, and the 350mm diamond saw blade should be placed in the original carton;
3. When using, you must wear protective covers, gloves, safety helmets, protective shoes, and protective glasses.
4. When installing the 350mm diamond saw blade, you must first confirm the performance and purpose of the saw table. It is best to read the saw table's manual first. In order to avoid incorrect installation and cause accidents.
5. When installing a 350mm diamond saw blade product, you must first check whether the alloy 350mm diamond saw blade is cracked, distorted, flattened, or tooth-dropped, etc., before installing it.
6. The serrations of 350mm diamond saw blade are super hard and sharp. It is forbidden to collide or fall on the ground. It must be handled with care.
7. After installing the alloy 350mm diamond saw blade, you must confirm whether the center hole of the 350mm diamond saw blade is firmly fixed on the flange of the saw table. If there is a gasket, the gasket must be set; then, gently push the 350mm diamond by hand The saw blade confirms whether the 350mm diamond saw blade rotates eccentrically. The diameter of the flange should be compatible with the 350mm diamond saw blade, and the size should be 1/3 of the diameter of the 350mm diamond saw blade slightly larger, and the thin piece should be a flange with a diameter of 1/2350mm diamond saw blade for better sawing results. ;
8. The cutting direction indicated by the arrow of the alloy 350mm diamond saw blade must be aligned with the rotation direction of the saw table. It is strictly forbidden to install it in the opposite direction, the wrong direction will cause the gear to fall.
9. Pre-rotation time: After replacing the 350mm diamond saw blade, it needs to pre-rotate for one minute before use, so that cutting can be performed when the saw table enters the working state.
10. After the 350mm diamond saw blade has been used many times, clean the teeth of the 350mm diamond saw blade to remove the resin, wood chips and other debris attached to both sides of the teeth, otherwise the processing effect of the 350mm diamond saw blade will be better. Big impact
You need to pay attention to the above ten points when using 350mm diamond saw blade products. After these ten points are completed, 350mm diamond saw blade can be used better.

Keyword:

Scan the QR code to read on your phone

Xinguang Diamond

WeChat official account

Xinguang Diamond

Mobile phone QR code

Tel: 86 15179308190
Fax: 86 0793-5226507
Email: andy@chinaxinguang.com
Address: Industrial Park, tianfanjie Town, Poyang County, Jiangxi Province

Copyright: Jiangxi Xinguang Diamond Tools Co., Ltd
Gan ICP Bei no.12002000

This website supports IPv4 / IPv6 accessebsite construction: 300.cn-Nanchang